COUNTER A COUNT LOAD VALUE
???? ?? ? ?????? to ??????
? ??????
Counter A resets to this value if Reset to Count Load action is selected. To
enter a negative Count Load value, increment digit 6 to display a “-” sign.*
COUNTER B BATCH COUNT ENABLE
EXAMPLE : The counter display is used to indicate the total number of feet
used in a process. It is necessary to know the number of pulses for the desired
units to be displayed. The decimal point is selected to show the resolution in
hundredths.
Scale Factor = Desired Display Units x Decimal Point Position
Number of Pulses
Given that 128 pulses are equal to 1 foot, display total feet with a one-
hundredth resolution.
Scale Factor = 1.00 x 100
128
?????
?
?
??
??
????
????
?????
Scale Factor = 0.007812 x 100
Scale Factor = 0.7812
The Counter B Batch Count function internally counts the number of output
activations of the selected setpoint(s). The count source for the batch counter
can be SP1, SP2 or both. Batch counting is available in all count modes except
?????? ?
USER INPUT FUNCTION
Dual Counter, which uses an external input signal for Counter B.
?
?????
?
?
COUNTER B DECIMAL POINT POSITION
????? ? ? ???? ??????
??? ?????
This selects the decimal point position for Counter B. The selection will also
affect Counter B scale factor calculations.
DISPLAY
??
??????
??????
?????
MODE
No Function
Program Mode Lock-out
Inhibit
Maintained Reset
DESCRIPTION
User Input disabled.
See Programming Mode
Access chart (Module 3).
Inhibit counting for the
selected counter(s).
Level active reset of the
selected counter(s).
Freeze display for the selected
COUNTER B SCALE FACTOR
????? ? ??????? to ???????
? ???????
The number of input or batch counts is multiplied by the scale factor to
obtain the desired process value. A scale factor of 1.0000 will result in the
display of the actual number of input or batch counts. (Details on scaling
calculations are explained at the end of this section.)*
COUNTER RESET AT POWER-UP
?????
??????
?????
?????
?????
?????
??????
Store
Store and Reset
Display Select *
Display Intensity Level *
Setpoint 1 Reset *
Setpoint 2 Reset *
Setpoint 1 and 2 Reset *
counter(s) while allowing
counts to accumulate internally.
Edge triggered reset of the
selected counter(s) after
storing the count.
Advance once for each
activation.
Increase intensity one level
for each activation.
Reset setpoint 1 output.
Reset setpoint 2 output.
Reset both setpoint 1 and 2
outputs.
?? ???? ?
? ??
??
???
??
???? ?
???? ??
????
?????
Print Request
Serial transmit of the active
parameters selected in the Print
Options menu (Module 5).
The selected counter(s) will reset at each meter power-up.
??????
Print and Reset *
Same as Print Request followed
by a momentary reset of the
selected counter(s).
* Indicates Edge Triggered function. All others are Level Active functions.
SCALING FOR COUNT INDICATION
The counter ’s scale factor is factory set to 1, to provide one count on the
USER INPUT ASSIGNMENT
display for each pulse that is input to the unit. In many applications, there will
not be a one-to-one correspondence between input pulses and display units.
Therefore, it is necessary for the meter to scale or multiply the input pulses by
a scale factor to achieve the desired display units (feet, meters, gallons, etc.)
The Count Scale Factor Value can range from 00.0001 to 99.9999. It is
?????? ?
? ???? ?
???? ?
???? ?
????
important to note that the precision of a counter application cannot be improved
by using a scale factor greater than one. To accomplish greater precision, more
pulse information must be generated per measuring unit. The following formula
is used to calculate the scale factor.
Scale Factor = Desired Display Units x Decimal Point Position
Number of Pulses
WHERE:
Desired Display Units : Count display units acquired after pulses that occurred.
Number of Pulses : Number of pulses required to achieve the desired
display units.
Decimal Point Position :
0 = 1
0.0 = 10
0.00 = 100
0.000 = 1000
0.0000 = 10000
8
The User Input Assignment is only active when Counter B is enabled and the
user input selection perfroms a Reset, Inhibit or Store function on one or both
of the counters.
*For value entry instructions, refer to selection/value entry in the Programming
The Meter section.
Shaded area selections only apply when Counter B is enabled (Dual Count
mode or batch counter).
相关PDF资料
ASD1-33.000MHZ-ECT OSCILLATOR 33.000 MHZ 3.0V SMD
LD200400 COUNTER 4 DIGIT 2.25" 120VAC RED
ASD1-12.000MHZ-ECT OSCILLATOR 12.000 MHZ 3.0V SMD
PAXLC600 COUNTER 6-DIGIT BI-DIR COUNT
CUB7P120 COUNTER 8-DIGIT VOLTAGE RED
5652F1-5V LED RED T1 QUAD RT ANG 5V PCB
FXO-HC526R-125 OSC 125 MHZ 2.5V HCMOS SMD
183566 LED T-1 28V .100" BI-PIN BASE
相关代理商/技术参数
LD2006P0 功能描述:COUNTER 6 DIGIT DUAL 2.25" RED RoHS:是 类别:工业控制,仪表 >> 计数器 系列:LD 其它有关文件:Declaration of Conformity 标准包装:1 系列:99766 计数速率:25Hz 数字/字母数:5 输入类型:机电式脉冲 输出类型:- 电源电压:24V 显示器类型:十进制拨轮
LD-201 制造商:ROHM 制造商全称:Rohm 功能描述:Flat displays
LD201C105KAB1A 功能描述:多层陶瓷电容器MLCC - SMD/SMT 100volts 1uF 10% 2220 X7R RoHS:否 制造商:American Technical Ceramics (ATC) 电容:10 pF 容差:1 % 电压额定值:250 V 温度系数/代码:C0G (NP0) 外壳代码 - in:0505 外壳代码 - mm:1414 工作温度范围:- 55 C to + 125 C 产品:Low ESR MLCCs 封装:Reel
LD201C105KAB2A 功能描述:多层陶瓷电容器MLCC - SMD/SMT 1.0UF 100V 10% RoHS:否 制造商:American Technical Ceramics (ATC) 电容:10 pF 容差:1 % 电压额定值:250 V 温度系数/代码:C0G (NP0) 外壳代码 - in:0505 外壳代码 - mm:1414 工作温度范围:- 55 C to + 125 C 产品:Low ESR MLCCs 封装:Reel
LD201C105KAB9A 功能描述:多层陶瓷电容器MLCC - SMD/SMT 100volts 1uF 10% 2220 X7R RoHS:否 制造商:American Technical Ceramics (ATC) 电容:10 pF 容差:1 % 电压额定值:250 V 温度系数/代码:C0G (NP0) 外壳代码 - in:0505 外壳代码 - mm:1414 工作温度范围:- 55 C to + 125 C 产品:Low ESR MLCCs 封装:Reel
LD201C475KAB2A 功能描述:多层陶瓷电容器MLCC - SMD/SMT 100volts 4.7uF 10% 2220 X7R RoHS:否 制造商:American Technical Ceramics (ATC) 电容:10 pF 容差:1 % 电压额定值:250 V 温度系数/代码:C0G (NP0) 外壳代码 - in:0505 外壳代码 - mm:1414 工作温度范围:- 55 C to + 125 C 产品:Low ESR MLCCs 封装:Reel
LD201C475KAX2A 功能描述:多层陶瓷电容器MLCC - SMD/SMT 100volts 4.7uF 10% X7R 2220 SIZE RoHS:否 制造商:American Technical Ceramics (ATC) 电容:10 pF 容差:1 % 电压额定值:250 V 温度系数/代码:C0G (NP0) 外壳代码 - in:0505 外壳代码 - mm:1414 工作温度范围:- 55 C to + 125 C 产品:Low ESR MLCCs 封装:Reel
LD2021MG 制造商:未知厂家 制造商全称:未知厂家 功能描述:Optoelectronic